Boiler Disposal

Guide · Homeowners · 4 min read · Updated 16 November 2026

Switching From a Gas Boiler to a Heat Pump: Removing the Old System

Short answer

When you switch from a gas boiler to a heat pump, the old boiler is disconnected by a Gas Safe registered engineer and removed. A combi boiler home may need a new hot water cylinder, while a home with an old cylinder and loft tanks may have them replaced or removed. If gas is no longer used, you can ask your supplier about removing the meter. Most installers include removal of the old boiler.

Switching From a Gas Boiler to a Heat Pump: Removing the Old System

What changes when you fit a heat pump

An air source or ground source heat pump replaces the boiler as the heat source for your radiators or underfloor heating, and usually heats hot water stored in a cylinder. Unlike a combi boiler, a heat pump does not heat water instantly on demand, so homes with combis normally need a cylinder fitting. Homes with an existing cylinder often have it replaced with one designed for heat pumps, which has a larger coil.

Some radiators may also be swapped for larger ones, because heat pumps run at lower flow temperatures. That means the switch can produce more old equipment than people expect: boiler, cylinder, loft tanks, radiators and pipework.

Planning the changeover

A heat pump installation usually takes several days, and for part of that time you may have no heating or hot water. Your installer should give you a schedule showing when the old boiler will be disconnected and when the new system will be running. Plan around cold weather if you can, and make sure you have a way to boil water and stay warm if the work overruns.

Clear the areas the installer needs: around the boiler, the airing cupboard, the loft hatch and the space outside where the heat pump will sit. Old equipment comes out through the house, so protect floors and move fragile items from hallways and landings. If you have belongings stored in the loft near the tanks, move them before the installers arrive.

Who does what

Heat pump installers under schemes such as the Microgeneration Certification Scheme (MCS) normally handle most of this, including removal of the old boiler. Check what is included in your quote before you sign.

ItemWho handles itNotes
Gas boiler disconnectionGas Safe registered engineerGas supply capped safely
Boiler and flue removalInstaller or removal serviceFlue opening made good
Old cylinder and loft tanksInstaller or removal serviceDrained first
Radiators replacedInstallerOld radiators recycled as scrap
Gas meterYour gas supplier or networkOnly if no gas appliances remain
New electrical supply for heat pumpElectricianNotifiable work

Disconnecting and removing the boiler

Any work on a gas appliance must be done by a Gas Safe registered engineer. The engineer turns off and disconnects the boiler and caps the gas pipe. The boiler is then drained, unbolted from the wall and taken away, and the flue is removed. The hole in the external wall left by the flue is filled and made good, inside and out.

If you still have a gas hob or gas fire, the gas supply stays. If the boiler was your only gas appliance and you do not plan to use gas again, you can ask your supplier about having the meter removed, which avoids standing charges. Your supplier or network operator will explain the process and any charges.

Old cylinders and loft tanks

Older homes with a regular boiler often have a copper hot water cylinder in an airing cupboard and a cold water storage tank and a small feed and expansion tank in the loft. When a heat pump system with an unvented cylinder is installed, the loft tanks are often no longer needed. They must be drained and disconnected, and the pipes capped, before they can come out.

Loft tanks are awkward to remove because they were often installed before the loft hatch was fitted or are too big to pass through it. Plastic tanks can be cut up in the loft. Older galvanised steel tanks are heavy and sometimes older tanks or their lids can contain asbestos, so check before cutting anything. Guide prices for cylinder and loft tank removal are about £90–£180.

  • Drain tanks fully before work starts, as even a small amount of water is heavy.
  • Protect the loft hatch area and the landing below.
  • Check old tanks and lids for possible asbestos before cutting.
  • Cap redundant pipes and remove them where accessible.
  • Recycle copper cylinders and pipe as scrap metal.

Radiators and pipework

If radiators are being upsized, the old ones are drained and removed. Old steel radiators can be recycled as scrap metal. Cast-iron column radiators can have resale value if they are in good condition, as they are popular in period properties. Redundant copper pipework is also worth recycling.

Old radiators collected separately start from about £10 each through a removal service.

Grants and paperwork

In England and Wales, the Boiler Upgrade Scheme offers a grant towards the cost of a heat pump installed by an MCS certified installer, replacing fossil fuel heating. Scotland has its own support schemes. The rules and amounts can change, so check the current details on the government website or with your installer.

Keep paperwork from the installation, including the MCS certificate, the Gas Safe engineer's disconnection record and waste transfer notes for removed equipment, with your property records.

When to use a separate removal service

Most installers include removal of the boiler and other equipment, but some quotes leave out old tanks, radiators or items stored elsewhere in the house. If your installer does not include them, or you have old boilers and cylinders left from previous work in a garage or shed, a removal service can collect them. Prices start from about £40 for a wall-hung boiler and £90–£180 for a cylinder and loft tanks.

Questions people also ask

Do I need to remove my gas boiler to get a heat pump?

Usually yes, if the heat pump is replacing it as your main heating. Some homes use a hybrid system where a heat pump works alongside a boiler, in which case the boiler stays. Your installer will advise on what suits your home.

Can I get my gas meter removed?

If you no longer use any gas appliances, you can ask your gas supplier about removing the meter and disconnecting the supply. This stops standing charges. There may be a charge depending on your supplier and network.

What happens to my old hot water cylinder?

If a new heat pump cylinder is fitted, the old one is drained, disconnected and removed. Copper cylinders are recycled as scrap metal. Your installer usually includes this, but check your quote.

Written and checked by the Boiler Disposal team. Read our editorial policy.

Get a free boiler disposal quote

Tell us what you need and we'll come back with a clear price.

Request a quote